You are here: News & Pressinfo / Events / Previous Events
Tuesday, January 26, 2021

Previous Events

Page 1 of 9 123456789 >>

10 December 2020
Web-Seminar English

We are happy to announce the new version of COPRA FEA RF 2020.2.

In this 20-minute online session our design engineer Lander Arrupe will introduce you to the new functionalities and answer your open questions.

Please register your attendance here:

The webinar will cover the following topics:

  • Simulations Queue - Prepare your simulations and start them from a Queue
  • Manual Mesh Modification - Local Refinement in Thickness Direction
  • Hole Meshing Capabilities - Punch holes in Bending Zones
  • Prediction of Wear Areas in the Profile - Better insight on the forming process
  • Your Questions

We look forward to your participation in our upcoming “COPRA FEA RF 2020.2 Release WebSeminar”:

We offer two sessions:

  • 9.00 am CEST
  • 3.00 pm CEST

23 July 2020
Web-Seminar English

The real world is an expensive medium for experimentation. Virtual environments allow us to test a larger number of ideas faster, at lower cost, and with less risk.

Please register your attendance here:

For roll formers COPRA FEA RF is the ideal playground for verifying new designs and also gaining valuable experience with pre- and post-processing steps.

In this 45-minute online session our design engineer Lander Arrupe will take you deeper into this topic and guide you through the process of simulating an embossing process by utilizing the advanced functionalities of COPRA FEA RF.

The webinar will cover the following topics:

  • Importing of CAD Tooling in a COPRA FEA RF Model
  • Defining the movement of the tooling and positioning it in the model
  • Creating contact bodies for the tooling and defining the contact table
  • Refining the mesh in the embossing zone
  • Adding a new load case to the model and to the job

We look forward to your participation in our upcoming “Embossing Simulation” webinar:

We offer two sessions:
9.00 am CEST
3.00 pm CEST

Please register your attendance here:

23 April 2020
Web-Seminar English

Lander is already in the starting blocks for another round of life-hacks. In this 20-minute session you can learn a few simple tips and tricks which make working with COPRA® FEA RF more proficient and fun. Join Lander on April 23rd, 2020 for these webinar highlights:

  • Automatic report, how to create user specific setup
  • Defining a user specific free cut position and geometry
  • Drawing dies as station entry support
  • How to overcome difficulties in defining the meshing reference with flowers with material additions/calibration or change of unfolding point
  • Fast analysis to define the position of the bending areas in the mesh
  • middle mouse button for help
  • new animation area
  • e-mail notification

At the end of the webinar there will also be some time for your questions. Please register here:

23 January 2020 - 28 January 2020
Location: BIEC, Bangalore, India

IMTEX FORMING 2020 attracts leading national and international manufacturing firms from the metal forming sector.

We will be present at this important exhibition together with our team from our Indian office. There data M Software India represents the COPRA® brand in this important market. The team in Pune, Maharashtra also provides wide-ranging consulting and engineering services - ensuring to respond to the growing demand for locally produced, high quality products and machinery.

Our team is looking forward to meeting you in Bangalore soon!

Organizer: Indian Machine Tool Manufacturers' Association (IMTMA) (

Location: Bangalore International Exhibition Centre (BIEC)

Stall B120 in Hall 3A

09 December 2019 09:00 - 17:00

Together with our partner in Turkey, Netform and Bias, we look forward to inviting you to our one-day COPRA® Seminar in Istanbul.

We are proud to announce that Dr. Okan Görtan (Hacettepe Üniversitesi) will be commencing the event with a presentation on "Roll-forming of Ultra High Strength Steels, Science or Art?"

A topic which will surely be of great interest for the industry that is challenged by ever-growing demands

During the seminar participants will learn how data M has been advancing its COPRA® EcoSystem and working on future-prove solutions.We will present some examples from the industry and give an outlook on the future of roll forming.

This session is recommended for a wide variety of attendees, for both prospects and existing customers alike.

Please refer to the detailed agenda .

The presentations will be given in English language.

45 Day Trial of Software

For those attending, there will also be a rare opportunity of a 45 day trial of our COPRA® software after the event at your facility.

Please register by sending an email to

28 November 2019 09:00 - 10:00
Web-Seminar English

Click "register here" to see your local time!

About this webinar:

Improve your design performance with five simple COPRA® RF life hacks:

In our upcoming webinar, data M design engineer and COPRA® power-user Lander Arrupe will be showing you his must-know life hacks for a faster and more efficient roll design.

“I will share with you some of my favorite but yet less-known features in COPRA® RF that will make a huge difference in your every-day roll design – for example copying of flower parts into a different cross section.”

Join Lander for the 20 minutes session that will enhance your Copra® skills in an instant. At the end of the webinar there will also be some time for your questions.

The number of participants is limited. Only persons registered in writing are admitted. If too few participants register for the seminar, we reserve the right to cancel the event at short notice.

Organizer: data M Sheet Metal Solutions GmbH

20 November 2019 - 23 November 2019

METALEX 2019 runs this year under the theme of “New Smart Technologies” – the perfect slogan that summarizes the many smart technologies that we offer for the roll forming industry.
Visit our booth within the “German Pavilion” # AP06 and let our team know about your roll forming projects.
We look forward to a vivid exchange with you.
We will also bring our latest software release – please stop by and we show you what the latest version of COPRA® RF and COPRA® FEA RF has to offer and how you can benefit from our developments.
See you soon in Bangkok

Organizer: Reed Tradex
Location: Bangkok International Trade & Exhibition Centre

19 November 2019 - 21 November 2019

19th-21st November, 2019 - International Symposium on Roll Forming Technology, Guangzhou
The 2019 International Symposium on Roll Forming Technology (Roll Forming 2019) will be held in Guangzhou, China on November 19-21, 2019.

Managing Director Albert Sedlmaier will be giving a presentation on the topic “Digitalization and Design”.
We will be joined in this event with our local partner AutoCAE. If you are interested in a meeting and discussing your roll forming needs, please give us a call or send us a mail.
We look forward to seeing you in Guangzhou
Organizer: The Chinese Society for Metals and China Steel Construction Society
Location: Country Garden Airport Phoenix Hotel Kanton

11 November 2019 - 13 November 2019

We look forward to your visit at our booth #A5022 at this year’s Fabtech in Chicago.

The Fabtech is one of the largest trade fairs for metal working in North America and the perfect location for spotting the latest developments in this sector.
Of course, we will also be there to demonstrate our state-of-the-art COPRA® technologies for the roll forming industry!

As an absolute highlight of this year’s show:
Our colleagues Carl Stephenson and Stefan Steininger will be offering “The Power of COPRA®” workflow demonstrations right at our booth.

Monday 11th, Tuesday 12th and Wednesday 13th November
Each day 11:00 – 12:30

Booth #A5022, Fabtech 2019, McCormick Place, 2301 S. Martin Luther King Drive, Chicago, IL 60616

Numbers will be limited so early registration is essential.
For registration, please send a mail to

These sessions are recommended for a wide variety of attendees, for both our long-term valued customers and those interested in becoming. The content will appeal to decision makers, supervisors, engineers, tool room personnel, management and students.

Further details on the seminar you can find in the attached PDF.

If you can’t make it to the booth demo, just drop by whenever convenient!
We look forward to seeing you in Chicago!

Location: #A5022
McCormick Place, 2301 S. Martin Luther King Drive,...

23 October 2019 - 26 October 2019

MECT is one of the biggest machine tool exhibitions in Japan.

During the show Managing Director Albert Sedlmaier will be demonstration visitors our COPRA® EcoSystem in which we unite all our commercial applications we offer for the roll forming industry.

Visit our booth inside the Bavarian Pavillion #1B49

We look forward to seeing you in Nagoya

Organizer: Bayern International
Location: Port Messe Nagoya
2-2 Kinjyo-futo, Minato-ku, Nagoya, 455-0848, Japan  
Booth: #1B49

Page 1 of 9 123456789 >>